Page 1 of 1
VyOS interfaces numeration
Posted: Wed Nov 01, 2017 4:02 am
by akopylov
Hello there.
I have VyOS 1.1.7 in my EVE-NG lab (2.0.3-84) ant it seems that it works fine, but there is a problem with interfaces numeration. There are 4 interfaces in VyOS: eth1-eth4 but on EVE-NG map they are named as eth0-eth3 and I can`t see any logic or conformity in the name scheme. E.g. during my first try the scheme was:
vyos eth1 = eve eth1
vyos eth2 = eve eth2
vyos eth3 = eve eth0
vyos eth4 = eve eth3
And during my second try the name scheme was:
vyos eth1 = eve eth0
vyos eth2 = eve eth2
vyos eth3 = eve eth3
vyos eth4 = eve eth1
Any thoughts how to fix it?
Re: VyOS interfaces numeration
Posted: Thu Nov 02, 2017 12:12 am
by ecze
using converted ova to qcow2 image and not observing such issue
Code: Select all
Last login: Sun Apr 10 19:16:48 UTC 2016 on tty1
Linux vyos 3.13.11-1-amd64-vyos #1 SMP Wed Aug 12 02:08:05 UTC 2015 x86_64
Welcome to VyOS.
This system is open-source software. The exact distribution terms for
each module comprising the full system are described in the individual
files in /usr/share/doc/*/copyright.
vyos@vyos:~$ sudo -i
root@vyos:~# ifconfig
eth0 Link encap:Ethernet HWaddr 50:18:00:07:00:00
inet6 addr: fe80::5218:ff:fe07:0/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:728 (728.0 B)
eth1 Link encap:Ethernet HWaddr 50:18:00:07:00:01
inet6 addr: fe80::5218:ff:fe07:1/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:668 (668.0 B)
eth2 Link encap:Ethernet HWaddr 50:18:00:07:00:02
inet6 addr: fe80::5218:ff:fe07:2/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:728 (728.0 B)
eth3 Link encap:Ethernet HWaddr 50:18:00:07:00:03
inet6 addr: fe80::5218:ff:fe07:3/64 Scope:Link
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:6 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 B) TX bytes:668 (668.0 B)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
inet6 addr: ::1/128 Scope:Host
UP LOOPBACK RUNNING MTU:65536 Metric:1
RX packets:98 errors:0 dropped:0 overruns:0 frame:0
TX packets:98 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:6976 (6.8 KiB) TX bytes:6976 (6.8 KiB)
Re: VyOS interfaces numeration
Posted: Fri Feb 05, 2021 12:31 am
by boxofstuff
I ran into this myself just now, the first device per lab is OK, but if you have multiple you will notice the issue.
I had made the image as per the how to doco.
The solution seems to be,
after you install VYOS onto the HDD and before you commit the image
from vyos, delete the configuration lines that bind the HWID to the interface then save and commit the configuration
Code: Select all
delete interfaces ethernet eth0 hw-id '50:00:00:01:00:00'
etc
Now in eve commit the changes to your disk as per the how to doco.