Page 1 of 2
XRV9k Support
Posted: Sat Apr 22, 2017 6:20 pm
by rajmohan
I am able to boot XRV9k 6.3.1. Everything goes fine except that the interfaces are not visible in the device.
Only the management interface is available.
I had tried to change the NIC type in XRV9k.php template file from virtio-net-pci to e1000.
Issue does not get resolved.
Any suggestions or tweaks to get the interfaces visible in XRV9k?
Re: XRV9k Support
Posted: Sun Apr 23, 2017 4:32 pm
by kmanthezu
i've been able to run the 9k with software version 5.4.0 I have not tried 6 code.
Re: XRV9k Support
Posted: Tue Apr 25, 2017 8:10 pm
by rajmohan
During boot, after initializing the interfaces, following messages are observed:
[ 0.108006] acpi PNP0A03:00: _OSC failed (AE_NOT_FOUND); disabling ASPM
[ 0.108547] acpi PNP0A03:00: fail to add MMCONFIG information, can't access extended PCI configuration space under this bridge.
This type of message is not being observed when booted using VMware ESXi / Workstation.
I could find the interfaces in Vmware scenario.
Any help / suggestion to avoid these errors in Qemu emulation
Re: XRV9k Support
Posted: Fri Apr 28, 2017 11:32 am
by ecze
next release will support xrv9k.
(Gitlab is already updated for full xrv9k support)
E.
Re: XRV9k Support
Posted: Fri Apr 28, 2017 3:09 pm
by mcat84
running on version
nxosv9k-7.0.3.I5.2
support vpc ....finally
Re: XRV9k Support
Posted: Tue May 09, 2017 2:21 pm
by steve.wonder
@ rajmohan
did you find any fix for your issue,
I've got the same problem with ios xrv9k 6.1.2,
I can boot it up, but only mgmt int is visible
I'm running eve ver 2.0.3-60
@ecze
that means xrv9k is not supported yet in eve ver am running?
Re: XRV9k Support
Posted: Tue May 09, 2017 8:30 pm
by slimy_cat
Found this:
sramtam
Code: Select all
For successful start of xrv9k ver 6.1.2 just change the qemu options in the template file(xrv9k.php) to:
$p['qemu_options'] = '-smbios type=1,manufacturer=cisco,product=CiscoIOSXRv9000 -cpu host -m 16384 -smp cores=4,threads=1,sockets=1 -enable-kvm -display none -serial mon:stdio -rtc base=utc -boot once=d';
Thanks to Rajmohan R.
Re: XRV9k Support
Posted: Tue May 09, 2017 9:48 pm
by steve.wonder
I applied the above, rebooted eve-ng, removed xrv hosts from the lab, added them again, booted up xrv9k and still the same
I noticed however, on 6.0.1, that when I checked on first logon, only mgmt was there. couple minutes later int gi0/0/0/0 turn up - weird
Any clue?
Re: XRV9k Support
Posted: Wed May 10, 2017 9:03 pm
by Uldis (UD)
next release will be fixed
Re: XRV9k Support
Posted: Tue Feb 06, 2018 8:14 pm
by numchucksoe
I am running 6.2.2 and the LC wont come up. I tried it with standard recent version and also tried the fix in the iosxr9k.php file and both show up with same issue.
Here is the console output of the LC failing.
Any ideas?
LC/0/0/CPU0:Feb 6 20:10:14.729 : processmgr[51]: %OS-SYSMGR-3-ERROR : dp_launcher(1) (jid 140) exited, will be respawned with a delay (slow-restart)
LC/0/0/CPU0:Feb 6 20:10:14.730 : processmgr[51]: %OS-SYSMGR-3-ERROR : dp_launcher(140) (fail count 5) will be respawned in 120 seconds